Ceramic Pro Care+
Ceramic Pro Care+ is a professional solvent-based nano-ceramic maintenance coating designed to restore and reinforce the hydrophobic and protective properties of existing nano-ceramic coatings. It may also be used as a stand-alone protective treatment, providing durable water repellency, improved surface slickness, and enhanced gloss. Its solvent-based formulation and longer-lasting performance are intended for professional application.
- AUTOMOTIVE
Product Class
Hydrophobic Surface Treatment / Maintenance Product / Hydrophobic Booster
Recommended Layers
1
Full Chemical Cure
72 hours
Consumption Per Layer
5 ml/m² per layer
Product Identification
- Product Name
- Ceramic Pro Care+
- Product Code
- NS400
- Product Version
- V1.0
- Manufacturer
- Nanoshine Group Corp.
- Country of Manufacture
- Taiwan (R.O.C.)
- TDS Revision
- V1.0-R3
- Issue Date
- 2026-09-01
Product Description
- Product Class
- Hydrophobic Surface Treatment · Maintenance Product · Hydrophobic Booster
- Formulation System
- Solvent-Based
- Solvent / Carrier Type
- Hydrocarbon-Based
- Component Configuration
- Single-Component (1K)
- Technology
- Nano-Ceramic Coating Technology
- System Role
- Stand-Alone Coating · Maintenance Layer · Booster
- Curing Mode
- Ambient Cure
- Coating Permanence
- Temporary (6-12 months)
- Primary Functions
- UV Protection · Hydrophobic Performance · Water Repellency · Contaminant Repellency · Self-Cleaning Performance · Reduced Surface Adhesion · Easier Maintenance · Surface Slickness · Gloss Enhancement
Typical Technical Properties
| Property | Value | Test Method / Standard |
|---|---|---|
| As Supplied | ||
| Density | 0.99 g/cm³ at 25 °C | Test Method / Standard: ASTM D1475 |
| Viscosity | 2-5 mPa·s at 20 °C | Test Method / Standard: ASTM D2196 |
| Cured Coating | ||
| Water Contact Angle | >105° | Test Method / Standard: ASTM D7334 |
The technical data stated in this document are based on internal laboratory testing, third-party testing where applicable, and current technical knowledge of the product.
Unless otherwise specified, all stated values are typical values obtained under controlled test conditions and are provided for technical reference. They should not be interpreted as guaranteed specification limits for every individual production batch.
Actual results may vary depending on substrate type and condition, application method, applied quantity or coating thickness, environmental conditions, curing conditions, and other application-specific factors. Where a specific test method, standard, substrate, or test condition is relevant to the interpretation of a reported value, it should be stated together with that value.
Appearance
- Liquid Appearance
- Clear, colorless, homogeneous liquid, free from visible particles or sediment
- Cured Appearance
- Clear and transparent · Additional Gloss · Original Appearance
Intended Use and Substrates
Ceramic Pro Care+ is primarily intended for professional maintenance of existing nano-ceramic coatings, particularly on automotive and other transportation surfaces. It is used to restore and reinforce hydrophobic performance, surface slickness, gloss, and overall coating behavior between major maintenance procedures, and may also be applied to other compatible coated surfaces where professional aftercare is required.
- Application Areas
- Automotive · Transportation · Marine · Residential · Commercial · Consumer & Luxury Goods · Household Applications
Suitable Substrates
- Painted & Coated Surfaces
- Automotive Paint · Clear Coat · Painted Surfaces · Powder-Coated Surfaces · Factory-Applied Coatings · Refinished Surfaces
- Metal Surfaces
- Bare Metal · Coated Metal · Polished Metal · Brushed Metal
- Glass & Transparent Surfaces
- Automotive Glass · Architectural Glass · Other Glass Surfaces
- Mineral & Ceramic Surfaces
- Ceramic · Porcelain · Natural Stone · Engineered Stone · Concrete · Masonry
- Polymer Surfaces
- Plastics · Acrylic · Polycarbonate · Other Polymer Surfaces
- Composite Materials
- Carbon Fiber · Fiberglass · Other Composite Materials
- Protective Films & Flexible Surface Materials
- PPF · Vinyl · Other Surface Films
- Leather & Leather-Like Materials
- Natural Leather · Synthetic Leather
- Wood-Based Surfaces
- Natural Wood · Finished Wood · Wood-Based Materials
- Rubber & Elastomeric Materials
- Rubber · Elastomers
- Surface Finish Compatibility & Retention
- Gloss — Preserved · Improved · Satin — Slightly Modified · Matte — Slightly Modified
- Use Environment
- Interior & Exterior
- Application Level
- Professional Application Recommended
Restrictions and Limitations
- Existing Surface Treatment Limitations
- Do not apply over existing waxes, sealants, hydrophobic treatments, or protective coatings unless specifically approved.
Surface Requirements
- Surface Cleanliness
- Fully Clean · Free from Oils, Grease, Silicone, Waxes, Polishing Residues, Existing Coatings (unrelated to the current build), and Other Contaminants
- Surface Moisture Condition
- Slightly Wet
- Surface Temperature
- Recommended range: 10–30 °C
- Existing Coating / Paint Condition
- Fully Cured · Fully Dried and Ready for Service
For complete substrate preparation procedures and product-specific preparation steps, refer to the current Installation Manual.
Application
- Application Method
- Spray Application · Wipe Application
- Recommended Ambient Temperature
- 25 °C
- Recommended Relative Humidity
- 50% RH
- Application Environment
- Clean, Dust-Free Indoor Area · Clean Controlled Area
- Recommended Layers
- 1
- Consumption Per Layer
- 5 ml/m² per layer
The application and curing times stated in this document are provided as reference values based on an ambient temperature of 25 °C, 50% relative humidity, and the typical coating thickness specified in this TDS. Actual timing may vary depending on substrate type and absorbency, application method, applied product quantity, final layer thickness after leveling, environmental conditions, and installer technique. The stated values should therefore be used as a technical reference rather than absolute process limits. During application, coating behavior should be observed and timing adjusted where necessary to achieve the intended result.
Application Timing and Curing
Flash Time
30 seconds after application
Flash Time for Ceramic Pro Care+: 30 seconds after application.
Levelling / Wipe-Off Window
approximately 60 seconds
Levelling / Wipe-Off Window for Ceramic Pro Care+: approximately 60 seconds.
Tack-Free Time
30 minutes
Tack-Free Time for Ceramic Pro Care+: 30 minutes.
Water Contact Restriction
24 hours
Water Contact Restriction for Ceramic Pro Care+: 24 hours.
Release for Service / Delivery
24 hours
Release for Service / Delivery for Ceramic Pro Care+: 24 hours.
Time Before Washing
72 hours
Time Before Washing for Ceramic Pro Care+: 72 hours.
Full Chemical Cure
72 hours
Full Chemical Cure for Ceramic Pro Care+: 72 hours.
For accelerated or alternative curing procedures (if available), refer to the current Installation Manual.
Storage and Shelf Life
- Storage Temperature
- 5–25 °C
- Storage Conditions
- Store in a dry place. Do not freeze, overheat, or expose to direct sunlight.
- Shelf Life — Unopened
- 2 years in sealed packaging
- After Opening
- Use as soon as possible after opening.
Packaging
- Primary Container
- Plastic Spray Bottle
- Secondary Packaging
- None
- Available Volumes
- 300 ml
Health and Safety
Chemical product. Handle and use in accordance with the current Safety Data Sheet (SDS) and product label.
Refer to the current product Safety Data Sheet (SDS) for complete information on hazards, safe handling, personal protective equipment, first aid, storage, disposal, transport, and emergency measures.
Frequently Asked Questions
How many layers should I apply?+
Recommended layers for Ceramic Pro Care+: 1, at 5 ml/m² per layer.
How long until the coating is fully cured?+
Ceramic Pro Care+ reaches full chemical cure in 72 hours.
When can the coated surface be washed after application?+
Wait 72 hours after applying Ceramic Pro Care+ before washing the surface.
When can the coated surface be exposed to rain or water?+
Keep a surface coated with Ceramic Pro Care+ away from water contact for 24 hours after application.
What surfaces is it suitable for?+
Ceramic Pro Care+ is suitable for painted & coated surfaces, metal surfaces, glass & transparent surfaces, mineral & ceramic surfaces, polymer surfaces, composite materials, protective films & flexible surface materials, leather & leather-like materials, wood-based surfaces, rubber & elastomeric materials.
What are the application temperature and humidity requirements?+
Apply Ceramic Pro Care+ at 25 °C and 50% RH, with the surface at 10–30 °C. Application environment: clean, dust-free indoor area, clean controlled area.
What is the shelf life, and how long after opening can it be used?+
Unopened, Ceramic Pro Care+ keeps for 2 years in sealed packaging, stored at 5–25 °C. Use as soon as possible after opening.
Can it be applied over another coating or wax?+
Do not apply Ceramic Pro Care+ over existing waxes, sealants, hydrophobic treatments, or protective coatings unless specifically approved. The surface must be fully clean, free from oils, grease, silicone, waxes, polishing residues, existing coatings (unrelated to the current build), and other contaminants.
How is it applied?+
Application methods for Ceramic Pro Care+: spray, wipe. Professional Application Recommended.
What does the cured coating look like?+
Cured Ceramic Pro Care+ is clear and transparent, additional gloss, original appearance.
How long does the coating last?+
Coating permanence for Ceramic Pro Care+: temporary (6-12 months).
The information and recommendations contained in this Technical Data Sheet are based on current product knowledge and the technical data available at the time of publication.
Actual product performance may vary depending on substrate type and condition, surface preparation, application method, environmental conditions, curing conditions, subsequent maintenance, and conditions of use. The product must be applied in accordance with the specified requirements and the current Installation Manual.
Users are responsible for verifying product suitability for the intended substrate and application, particularly where materials, conditions, or uses fall outside those specifically described or validated by the manufacturer.
This Technical Data Sheet does not replace the applicable Safety Data Sheet (SDS). Refer to the current product SDS for complete information regarding hazards, safe handling, personal protective equipment, first aid, storage, disposal, and emergency measures.
For complete surface preparation, application, curing, and installation procedures, refer to the current Ceramic Pro Installation Manual applicable to the product.
Always refer to the most recent published version of this Technical Data Sheet. Product specifications, formulations, recommendations, and supporting documentation may be updated as part of ongoing product development and technical review.
This document does not modify or replace any applicable product warranty terms or other contractual conditions.