Ceramic Pro Textile
An eco-friendly protective spray-coating for natural textiles, suede, and absorbent materials. Delays wear and tear and lets you enjoy your favorite clothes or furniture for longer.
Ceramic Pro Textile is a water-based superhydrophobic treatment for highly absorbent fibrous and porous materials. It penetrates into absorbent substrates and modifies their surface behavior to produce a water contact angle above 150°, providing strong resistance to water and liquid contamination. The product is intended for natural and other highly absorbent materials such as textile, suede, and paper, and is not suitable for non-absorbent synthetic surfaces.
- AUTOMOTIVE
- AVIATION
- GARMENTS & FOOTWEAR
- HOME
- MARINE
Product Class
Hydrophobic Surface Treatment
Recommended Layers
1
Full Chemical Cure
72 hours
Consumption Per Layer
5-10 ml/m²
Product Identification
- Product Name
- Ceramic Pro Textile
- Product Code
- T1500
- Product Version
- V1.0
- Manufacturer
- Nanoshine Group Corp.
- Country of Manufacture
- Taiwan (R.O.C.)
- TDS Revision
- V1.0-R3
- Issue Date
- 2026-09-01
Product Description
- Product Class
- Hydrophobic Surface Treatment
- Formulation System
- Water-Based
- Solvent / Carrier Type
- Water
- Component Configuration
- Single-Component (1K)
- Technology
- Nano-Ceramic Coating Technology
- System Role
- Stand-Alone Coating
- Layering Type
- Single-Layer Coating
- Curing Mode
- Ambient Cure
- Coating Permanence
- Temporary (6-12 months)
- Primary Functions
- Environmental Contaminant Protection · Stain Resistance · Hydrophobic Performance · Water Repellency · Contaminant Repellency · Self-Cleaning Performance · Reduced Surface Adhesion · Easier Maintenance
Typical Technical Properties
| Property | Value | Test Method / Standard |
|---|---|---|
| As Supplied | ||
| Density | 0.95-1 g/cm³ at 25 °C | Test Method / Standard: ASTM D1475 |
| Viscosity | <5 mPa·s at 20 °C | Test Method / Standard: ASTM D2196 |
| Cured Coating | ||
| Water Contact Angle | 150° | Test Method / Standard: ASTM D7334 |
The technical data stated in this document are based on internal laboratory testing, third-party testing where applicable, and current technical knowledge of the product.
Unless otherwise specified, all stated values are typical values obtained under controlled test conditions and are provided for technical reference. They should not be interpreted as guaranteed specification limits for every individual production batch.
Actual results may vary depending on substrate type and condition, application method, applied quantity or coating thickness, environmental conditions, curing conditions, and other application-specific factors. Where a specific test method, standard, substrate, or test condition is relevant to the interpretation of a reported value, it should be stated together with that value.
Appearance
- Liquid Appearance
- Clear, colorless, homogeneous liquid, free from visible particles or sediment
- Cured Appearance
- Clear and transparent · Non-Reflective
Intended Use and Substrates
Ceramic Pro Textile is intended for the protection of water-absorbing surfaces such as textile, suede, and other compatible porous materials. It may be used on automotive interiors as well as on furniture, upholstery, curtains, clothing, footwear, and other suitable household, commercial, or consumer products.
- Application Areas
- Automotive · Transportation · Residential · Commercial · Consumer & Luxury Goods · Household Applications
Suitable Substrates
- Textile Materials
- Fabric · Textile · Carpet · Upholstery
- Surface Finish Compatibility & Retention
- Gloss — Preserved · Satin — Preserved · Matte — Preserved
- Use Environment
- Interior & Exterior
- Application Level
- Professional Use / Consumer / DIY Use
Restrictions and Limitations
- Substrate Deformation Limitations
- Not suitable for non-water-absorbing substrates such as synthetic fibers or natural water-repelling fibers.
- Existing Surface Treatment Limitations
- Do not apply over existing waxes, sealants, hydrophobic treatments, or protective coatings unless specifically approved.
Surface Requirements
- Surface Cleanliness
- Fully Clean · Free from Oils, Grease, Silicone, Waxes, Existing Coatings (unrelated to the current build), and Other Contaminants
- Surface Moisture Condition
- Fully Dry
- Surface Temperature
- Recommended range: 10–30 °C
For complete substrate preparation procedures and product-specific preparation steps, refer to the current Installation Manual.
Application
- Application Method
- Spray Application · Dip Application
- Recommended Ambient Temperature
- 25 °C
- Recommended Relative Humidity
- 50% RH
- Application Environment
- Clean, Dust-Free Indoor Area
- Recommended Layers
- 1
- Consumption Per Layer
- 5-10 ml/m²
The application and curing times stated in this document are provided as reference values based on an ambient temperature of 25 °C, 50% relative humidity, and the typical coating thickness specified in this TDS. Actual timing may vary depending on substrate type and absorbency, application method, applied product quantity, final layer thickness after leveling, environmental conditions, and installer technique. The stated values should therefore be used as a technical reference rather than absolute process limits. During application, coating behavior should be observed and timing adjusted where necessary to achieve the intended result.
Application Timing and Curing
Flash Time
30 seconds after application
Flash Time for Ceramic Pro Textile: 30 seconds after application.
Levelling / Wipe-Off Window
approximately 60 seconds
Levelling / Wipe-Off Window for Ceramic Pro Textile: approximately 60 seconds.
Tack-Free Time
30 minutes
Tack-Free Time for Ceramic Pro Textile: 30 minutes.
Water Contact Restriction
24 hours
Water Contact Restriction for Ceramic Pro Textile: 24 hours.
Release for Service / Delivery
24 hours
Release for Service / Delivery for Ceramic Pro Textile: 24 hours.
Time Before Washing
72 hours
Time Before Washing for Ceramic Pro Textile: 72 hours.
Full Chemical Cure
72 hours
Full Chemical Cure for Ceramic Pro Textile: 72 hours.
For accelerated or alternative curing procedures (if available), refer to the current Installation Manual.
Storage and Shelf Life
- Storage Temperature
- 5–25 °C
- Storage Conditions
- Store in a dry place. Do not freeze, overheat, or expose to direct sunlight.
- Shelf Life — Unopened
- 2 years in sealed packaging
- After Opening
- Use as soon as possible after opening.
Packaging
- Primary Container
- Plastic Spray Bottle
- Secondary Packaging
- None
- Available Volumes
- 300 ml
Health and Safety
Chemical product. Handle and use in accordance with the current Safety Data Sheet (SDS) and product label.
Refer to the current product Safety Data Sheet (SDS) for complete information on hazards, safe handling, personal protective equipment, first aid, storage, disposal, transport, and emergency measures.
Frequently Asked Questions
How many layers should I apply?+
Recommended layers for Ceramic Pro Textile: 1, at 5-10 ml/m².
How long until the coating is fully cured?+
Ceramic Pro Textile reaches full chemical cure in 72 hours.
When can the coated surface be washed after application?+
Wait 72 hours after applying Ceramic Pro Textile before washing the surface.
When can the coated surface be exposed to rain or water?+
Keep a surface coated with Ceramic Pro Textile away from water contact for 24 hours after application.
What surfaces is it suitable for, and what surfaces is it not?+
Ceramic Pro Textile is suitable for textile materials. Not suitable for non-water-absorbing substrates such as synthetic fibers or natural water-repelling fibers.
What are the application temperature and humidity requirements?+
Apply Ceramic Pro Textile at 25 °C and 50% RH, with the surface at 10–30 °C. Application environment: clean, dust-free indoor area.
What is the shelf life, and how long after opening can it be used?+
Unopened, Ceramic Pro Textile keeps for 2 years in sealed packaging, stored at 5–25 °C. Use as soon as possible after opening.
Can it be applied over another coating or wax?+
Do not apply Ceramic Pro Textile over existing waxes, sealants, hydrophobic treatments, or protective coatings unless specifically approved. The surface must be fully clean, free from oils, grease, silicone, waxes, existing coatings (unrelated to the current build), and other contaminants.
How is it applied?+
Application methods for Ceramic Pro Textile: spray, dip. Professional Use / Consumer / DIY Use.
What does the cured coating look like?+
Cured Ceramic Pro Textile is clear and transparent, non-reflective.
How long does the coating last?+
Coating permanence for Ceramic Pro Textile: temporary (6-12 months).
The information and recommendations contained in this Technical Data Sheet are based on current product knowledge and the technical data available at the time of publication.
Actual product performance may vary depending on substrate type and condition, surface preparation, application method, environmental conditions, curing conditions, subsequent maintenance, and conditions of use. The product must be applied in accordance with the specified requirements and the current Installation Manual.
Users are responsible for verifying product suitability for the intended substrate and application, particularly where materials, conditions, or uses fall outside those specifically described or validated by the manufacturer.
This Technical Data Sheet does not replace the applicable Safety Data Sheet (SDS). Refer to the current product SDS for complete information regarding hazards, safe handling, personal protective equipment, first aid, storage, disposal, and emergency measures.
For complete surface preparation, application, curing, and installation procedures, refer to the current Ceramic Pro Installation Manual applicable to the product.
Always refer to the most recent published version of this Technical Data Sheet. Product specifications, formulations, recommendations, and supporting documentation may be updated as part of ongoing product development and technical review.
This document does not modify or replace any applicable product warranty terms or other contractual conditions.